Fascia and Soffit Replacement: What Actually Happens

Day by day, what a proper roofline replacement involves — and the corners that get cut when it is done cheaply.

Call 07476 888638 for a free, no-obligation quote. Available Mon–Sun, 9am–6pm.

Roofline replacement is one of the most commonly mis-sold jobs in the trade, because from the ground a good installation and a bad one look identical for the first two years. The difference is all in what happens to the timber behind the new boards.

This guide walks through what we do, in order, so you can ask the right questions of whoever ends up doing your work.

Before the work: the survey

The survey establishes the length of each run, the depth of the existing fascia, the type of eaves detail, whether there is a soffit at all, and — most importantly — the condition of the rafter feet behind the board.

It also determines access. Most two-storey semis can be done from towers and ladders safely; three-storey terraces, properties over conservatories, and anything with a steep bank behind it usually need scaffold, and that cost belongs in the quote from the start.

Day one: strip out

Guttering comes off first, then the old fascia and soffit. This is the moment of truth. Rotten rafter feet, previously hidden, become visible; so does any earlier capping-over job, where a previous contractor screwed uPVC over decaying timber rather than removing it.

The bottom two courses of tiles or slates are lifted to expose the eaves and to allow the new board and felt support tray to be fitted correctly. On a roof with no felt at all — common on older slate roofs here — an eaves tray is fitted to carry water into the gutter.

  • All old timber removed, not capped over
  • Rafter feet inspected individually
  • Rotten rafter ends cut back and spliced with treated timber
  • Eaves course lifted to allow correct detailing
  • Felt support tray fitted where the underlay is short or absent

Day one to two: new roofline installed

New fascia is fixed directly to sound rafter feet with stainless or polymer-coated fixings — never to the old board. Soffit is fitted into a channel or joint trim so it can move without cracking, and ventilation is built in at this stage.

Ventilation is the detail most often skipped. A continuous 10mm airflow path at the eaves — through soffit vent strips or over-fascia vents — is what stops your newly insulated loft from developing condensation. It costs very little to include and is expensive to retrofit.

New guttering is then hung to a consistent fall towards the outlet, with brackets at correct centres rather than wherever the old ones were.

Typical timescales

Most domestic roofline jobs are quick. The variable is how much timber repair is found on strip-out.

Shortcuts to watch for

Capping — cladding over the existing timber with a thin uPVC sheet — is the big one. It is quicker, cheaper and it seals rotten wood inside a plastic jacket where it continues to decay unseen.

Other common shortcuts: reusing old gutter brackets, fixing into the old fascia rather than the rafter, omitting ventilation entirely, and leaving the eaves course of tiles unlifted so the new board sits proud of the felt line.

Ask directly: is the old timber being removed, and is ventilation included? Both answers should be yes, in writing.

After the work

All waste should be removed, gutters flow-tested with water rather than eyeballed, and the finished work walked round with you. We photograph any timber repairs before they are covered up, so you can see what was done behind the board.

Want a professional to handle it?

Get Your Free, Personalised Quote

Tell us about your roofing job and we'll get back to you as soon as possible.

No spam, no obligation. We'll get back to you as soon as possible.

Free Inspections
Fast Response
Reliable Workmanship
West Glamorgan Coverage

Questions

How long does fascia and soffit replacement take?

Two to three days for a typical three-bedroom semi, longer if rafter feet need repairing or if scaffold is required.

Do I need to be home?

Not for the whole job, but it is helpful to be available at strip-out so we can show you anything unexpected behind the old boards before it is covered.

Will you need to come inside?

Usually only to check the loft for ventilation and any signs of water at the eaves. The work itself is entirely external.

Is capping ever acceptable?

Only where the existing timber is genuinely sound and dry — which, on a board old enough to be replaced, is rare. We will tell you honestly if it is one of those cases.

Related services