Why Is My Roofline Rotting, and How Is It Fixed?

Timber does not rot because it is old. It rots because something is keeping it wet, and replacing the boards without fixing that just resets the clock.

Call 07476 888638 for a free, no-obligation quote. Available Mon–Sun, 9am–6pm.

A rotten roofline is almost always caused by water: a gutter that leaks or overflows, felt that stops short of the gutter, or poor ventilation letting damp build up behind the boards. The fix is to cure the cause, cut out the rotten timber and fit new boards, rather than cap over soft wood.

The roofline is the join between the roof and the walls, and it is where three separate systems meet: the tiles and felt above, the guttering in front, and the loft ventilation behind. When any one of them fails, the timber in the middle pays for it.

That is why we look at all three before quoting. Fitting new boards over a failed eaves detail is money spent on the symptom.

The four causes we find most

Nearly every rotten roofline we replace comes back to one of these, and often two at once.

  • Roof felt perished or dropped short, so water runs behind the gutter
  • Gutters overflowing or leaking at joints and soaking the fascia
  • Blocked or absent eaves ventilation trapping moisture in the loft
  • Paint left too long, letting water into end grain at the joints

Signs the rot has gone beyond the fascia

If a screwdriver sinks into the fascia, check the soffit underneath and, from the loft, the rafter ends behind it. Soft, dark rafter feet mean the water has been getting in for a while, and they need cutting back and renewing before any new board goes on.

Peeling paint, gutters pulling away and dark staining on the wall below are all early signs worth acting on before the rot spreads.

Why ventilation matters at the eaves

Warm damp air rises out of the house into the loft and needs somewhere to go. If the soffit is solid and there is no gap at the eaves, that moisture condenses on the cold underside of the felt and drips onto the timber and insulation below.

Vented soffit board, or over-fascia vents where the soffit cannot be vented, is a cheap thing to build into a roofline replacement and it stops the new timber from being asked to live in the same damp air the old one did.

Doing it once, properly

A roofline job done properly means stripping the old boards, checking and treating the rafter feet, fitting an eaves protector so the felt discharges into the gutter, adding ventilation where the roof needs it, then fitting the new uPVC and guttering.

Done that way, the new roofline is dry from day one and the maintenance really does drop to an occasional wash down.

Want a professional to handle it?

Get Your Free, Personalised Quote

Tell us about your roofing job and we'll get back to you as soon as possible.

No spam, no obligation. We'll get back to you as soon as possible.

Free Inspections
Fast Response
Reliable Workmanship
West Glamorgan Coverage

Questions

Can I just cap a rotten fascia with uPVC?

No. Capping is only for sound, dry timber. Rotten boards need removing and replacing or the rot carries on underneath.

What causes a fascia to rot?

Water from a leaking or overflowing gutter, felt that stops short of the gutter, or damp building up where the eaves are not ventilated.

Will uPVC stop the rot?

Only if the cause is dealt with at the same time. uPVC will not rot itself, but the rafter feet behind it still will if water is getting in.

Can rotten rafter ends be repaired?

Yes, in most cases the rafter feet can be cut back and spliced while the roofline is off, which is far cheaper than leaving it another few winters.

Is condensation in the loft the same problem?

It is closely linked. Blocked eaves ventilation causes both loft condensation and damp roofline timber, and both are fixed at the eaves.

How do I know which cause I have?

A look at the eaves from an access platform plus a look in the loft on a wet day usually answers it. We do both before quoting.

Related services