My Gutter Drips at the Joints, Not Over the Edge

A leak at a union is a different fault from an overflowing gutter, and the fix is different too.

Call 07476 888638 for a free, no-obligation quote. Available Mon–Sun, 9am–6pm.

Straight to it. If water drips steadily from the join between two lengths of gutter while the rest of the run stays dry on top, the problem is the union, not a blockage. Something has stopped that joint holding: the rubber seal has hardened, the gutter has moved out of the clip, or the bracket spacing is letting the run flex every time it fills.

It is worth fixing promptly even though it looks minor. A drip at a joint lands in the same spot every time it rains, and that steady soaking is what rots fascia boards, stains render and eventually finds its way into a wall.

Why unions leak

On PVC guttering, the union clips the two ends together and a moulded rubber gasket does the sealing. Almost every joint failure comes back to one of these.

  • The gasket has gone hard and flat with age and UV, so it no longer takes up movement
  • The gutter ends were pushed fully home with no expansion gap, so heat has forced the joint open
  • Brackets are too far apart, letting the run sag between them and pull at the joint
  • A ladder has been leant on the gutter and knocked a length out of true
  • Debris and grit sit in the seal, holding the joint fractionally open
  • The run falls the wrong way, so water pools at the joint instead of passing it

Cast iron is a different story

Older property in this area still carries a good deal of cast iron guttering. Those joints are bolted and bedded in mastic or putty, and they leak when the bedding perishes or the bolt rusts and loses tension. A cast iron joint can often be stripped, cleaned, re bedded and re bolted rather than replaced, which keeps the look of the building.

What kills cast iron is not the joint but the inside of the trough rusting once the paint has gone. If a section is scaling and thin, patching a joint is no longer the answer for that length.

What you can do safely, and where to stop

From the ground you can learn most of what matters. Watch during rain and see whether the water dripping at the joint is coming from a full trough or from a dry one.

  • Look along the run from below and check whether it dips between brackets
  • Note whether the drip is at every joint or just one, since every joint points at age
  • Check the fascia under the drip for dark, soft or flaking timber
  • Look for a green stripe on the wall, which shows the drip has been running for a long time

Why sealant is rarely the answer

The usual DIY fix is a bead of silicone over the outside of the joint. It works for a few months. Then the gutter expands, the bead shears, and water tracks behind it where you now cannot see it. Worse, the sealant makes a proper repair harder because the union has to be cleaned out before a new one will seat.

A joint that leaks because the run has no expansion gap will always beat sealant, because the movement is real and it happens every sunny day.

How we put it right

For a single failed union, we replace the union and gasket, reset the pipe ends with the correct expansion gap, and check the fall to the outlet along the whole run. For a sagging run we renew or add brackets at the right centres and reset the line.

Where the guttering is old enough that every joint is hardening, replacing the run is usually cheaper than repeated visits, and it is the moment to check the fascia behind it while the gutter is off. If the timber under the drip has gone soft, replacing guttering onto rotten fascia just hides the problem, so we will show you what is behind there before you decide.

Want a professional to handle it?

Get Your Free, Personalised Quote

Tell us about your roofing job and we'll get back to you as soon as possible.

No spam, no obligation. We'll get back to you as soon as possible.

Free Inspections
Fast Response
Reliable Workmanship
West Glamorgan Coverage

Questions

Can a single leaking gutter joint be repaired, or must the whole run be replaced?

A single joint on an otherwise sound run is a straightforward swap of the union and seal. Replacement makes more sense when several joints are weeping, which points to general age.

Will silicone sealant fix a leaking gutter joint?

Only briefly. The gutter moves with temperature and the bead shears, and then the water tracks behind it out of sight. It also has to be cleaned off before a proper repair.

Why does my gutter joint only leak on hot days?

It usually means the two lengths were pushed fully home with no expansion gap, so the joint is being forced apart as the plastic grows. Resetting the ends solves it.

Can old cast iron guttering be saved?

Often yes. Bolted joints can be stripped, cleaned, re bedded and re bolted. If the trough itself is scaling and thin, that length is past repair.

Is a dripping joint doing real damage?

It concentrates water in one place every time it rains, which rots the fascia and stains the wall. It is cheap to fix now and considerably less cheap once the timber has gone.

Related services