Damp Patches Down My Chimney Breast

The stack, the flashing and the flue each leave a different signature on the wall inside.

Call 07476 888638 for a free, no-obligation quote. Available Mon–Sun, 9am–6pm.

Here is the short version. Damp on a chimney breast is almost always one of four things: failed lead flashing where the stack meets the roof, open pointing or perished brickwork on the stack itself, a missing or ineffective cap on a disused flue, or condensation inside a cold flue that is no longer being used.

They look similar on the wall and they need completely different work, so identifying which one you have before anyone opens their toolbox saves a lot of money. Chimney leaks are one of the searches we see most often in this area, and in older Welsh stone and brick property the stack is very often the wet part of an otherwise sound roof.

Reading the pattern on the wall

Where the damp sits, and when it appears, does most of the diagnosis for you.

  • High on the breast, in the upstairs room or loft, straight after rain: flashing or the stack above the roof line
  • A vertical stripe following one edge of the breast: water running down the outside face of the flue
  • Brown or yellow staining with a tarry smell: an unused flue drawing damp through old soot deposits
  • Worst in cold snaps rather than wet ones: condensation in a cold, capped or blocked flue
  • Salty white bloom on the plaster: long standing moisture bringing salts out of the masonry

The flashing, and why it fails

Where a chimney passes through a pitched roof, the joint is weathered with lead: a front apron, side step flashings or soakers, and a back gutter behind the stack. The back gutter is the part that fails most, because it carries every drop of water the roof sheds above the stack.

Lead itself lasts a very long time. What fails is the pointing that holds the top edge into the brickwork, the fixing clips, and any cement fillet used instead of lead in the first place. A mortar fillet always cracks eventually, because mortar and lead move at different rates. If you can see a grey cement triangle where the stack meets the tiles, that is a repair waiting to happen.

The stack itself

A chimney above the roof is the most exposed masonry on the building. Rain hits it from every side and there is no roof over it. Once the pointing washes out or the bricks spall, the stack soaks up water and passes it inward and downward until it reaches plaster.

A disused flue makes this worse. With no fire drawing warm air up it, the flue stays cold and damp, and any moisture that gets in has nothing to dry it out. Capping the pot while leaving the flue vented at the bottom is often the difference between a dry breast and a permanently stained one.

What you can check without going up

Use binoculars or the zoom on your phone from the garden, and look at the stack from two sides.

  • Are the joints between bricks recessed, crumbling or missing mortar
  • Is there a cracked cement fillet instead of lead where the stack meets the tiles
  • Is the pot open to the sky on a flue you never use
  • Is the flaunching, the mortar bed the pot sits in, cracked or breaking away
  • In the loft, is the timber around the stack dark and damp, and is it wet after rain or in the cold

Putting it right properly

Depending on what we find, that means renewing lead flashings and raking the top edge back into a joint, repointing the stack, rebedding or replacing the flaunching, or fitting a capped and vented cowl to a disused flue. Where the internal plaster has been wet for years it may need hacking off and re rendering once the source is dry, which is a plasterer's job rather than ours, and we will tell you that plainly.

The wrong fix is sealing the inside face or coating the stack in waterproofer, which traps moisture in the masonry and often makes the staining worse the following winter.

Want a professional to handle it?

Get Your Free, Personalised Quote

Tell us about your roofing job and we'll get back to you as soon as possible.

No spam, no obligation. We'll get back to you as soon as possible.

Free Inspections
Fast Response
Reliable Workmanship
West Glamorgan Coverage

Questions

How do I tell a chimney leak from rising damp?

Height and timing. Rising damp stops around a metre above floor level and does not follow the rain. Chimney damp starts high on the breast or in the loft and responds within hours of a downpour.

Can a chimney leak if I never use the fire?

Yes, and unused flues are more likely to stain, because there is no warm draught drying them out. Capping the pot while keeping the flue ventilated is usually part of the answer.

Is a cement fillet an acceptable way to weather a chimney?

It is common on older work but it is not a durable detail. Mortar cracks away from lead and brick over time, and once it does the water goes straight in. Lead flashing is the proper fix.

Do I need scaffolding for chimney work?

For anything more than a look, usually yes. Working on a stack means working above the roof line, and access has to be safe. We will include it in the written quote rather than spring it on you.

Should I have the stack taken down instead?

Removal is worth considering if the flue is redundant and the stack is in poor condition, but it changes the roof line and needs making good properly. We will price repair and removal side by side if you want to compare.

Related services